Closed Loop Stepper motor Hybrid Integrated Stepper Servo Motor driver apply for sewing machine,Textile Machine,jacquard Machine,Embroidery Machine and all kinds of CNC machines.

一、Product Specification

The LT-PM02NXX series closed-loop servo motor is used for high-precision closed-loop motor products. The closed-loop servo motor has a specific remote communication function, which can achieve automation, remote control, and intelligence of motor control.

This document applies to closed-loop servo motors of LT-PM02N02, LT-PM02N03, LT-PM02N04, and LT-PM02N05.

二、Product rendering

According to the type of motor and installation method, it can be divided into the following models:

1. The motor type of LT-PM02N02 closed-loop servo motor is 42 motor, and the installation method is horizontal installation:

2. The motor type of LT-PM02N04 closed-loop servo motor is 42 motor, and the installation method is vertical installation

3. The motor type of LT-PM02N05 closed-loop servo motor is 35 motor, and the installation method is horizontal installation

4.The motor type of LT-PM02N03 closed-loop servo motor is 35 motor, and the installation method is vertical installation

六、Menu and Keypad

1. Digital tube display

Using a digital display, the position information is displayed under normal circumstances. If you long press [Settings], the corresponding menu information will be displayed.

2. Menu options

Supports four menu setting options (P1~P7), see below definitions:

（1）P1：Device address, representing the communication address of this device, with a setting range of 1-250;

（2）P2：Installation method selection, means the installation method of this device, 0 represents "A" or 1 represents "B" installation

（3）P3:Zero setting: Short press the [+] button on the zero position setting parameter interface to move forward one step, long press the [+] button to move forward continuously .same rule for(-) button，Simultaneously display rotating icons，The specific zero position is based on the motor's operating position (recommend to use this method to set the zero position);

（4）P4:Running speed, adjusting the speed of the motor during operation, setting levels 1-10 (default value 6)

（5）P5：Operating torque, adjust the size of motor operating torque, set levels 1-10 (default value 6)；

（6）P6：Maintain torque, adjust the motor to maintain torque, set levels 1-10 (default value of 6)

（7）P7：Language, indicating the language type of menu operation, supporting switching between Chinese and English;

Note 1：When setting parameter, remote communication with this device must be stopped first to prevent interference with the zero point setting.

Note 2;Once complete zero position adjustment, press [Set] button for 2 seconds to set the current position to zero

3. Key Function Description

The closed-loop servo motor provides three buttons, Below are definitions

（1）【Setting】：Long press，Press and hold for 2 seconds to enter the parameter setting interface. After setting the parameter values, press and hold for 2 seconds again to save the parameters; Short press to switch between menu and parameter items;

（2）【+】;Parameter value increases

（3）【-】;Parameter value decrease

Note;In the parameter setting interface, if there are no button operations for 60 seconds, the timeout will automatically return to the main interface (parameters will not be saved)

七、Remote Operation

1. Remote to modify Address

The address of this device can be remotely modified through the system within the first 20 seconds of each power on of the closed-loop servo motor. After the device automatically goes online after this time, remote modification of the device address is no longer allowed.

The system remotely modifies the device address, and the jacquard system tests the motor (Test ->Motor ->Single ->Address ->(Upper/Lower Disk) ->Address Positioning) as shown in pic4.

After completing the operation as shown in the above diagram, power on the closed-loop servo motor that needs to modify its address separately

Note：This operation should be used with caution. If the address is changed or the device is turned on for more than 20 seconds, it will automatically go online.

2. Remote zero position recognition

Run the motor to the corresponding position through testing, and then perform zero position recognition (testing ->motor ->single/all ->set address (single valid) ->upper/lower panel ->zero position recognition). The schematic diagram of zero position recognition is shown in Pic 5.

Once complete operation, the current position can be set to zero. Due to its relatively complex operation, Not recommended to use this method to set the zero position

3. Running tests

Test the jacquard system motor (test ->motor ->all ->test value 300->(upper/lower plate) ->start testing), check the operation of the motor, ensure that all motors are running normally, and the configuration interface is shown in pic #6

4. Running direction

（1）All devices are powered on, and the jacquard system is set (parameters ->system ->enable density motor). The interface is shown in Pic# 7

（2）Set the direction of motor operation, jacquard system settings (parameters ->jacquard ->general ->(lower/upper) density motor direction), interface as shown in Pic# 8

INTERFACE

                                Table 1 Definition of Power Interface

INSTALLATION DIAMENSIONS

SYSTEM CONNECTION DIAGRAM

diagram is shown in pic 11

Common Errors

Table 3 Common Failed Display

Specification